Dec 072018
 

On the 28th November we were treated to a talk on Amateur Satellites by Stephen 2E0SSM.   He started by talking about the different types of orbits in use by all satellites and then moved onto the more specific orbits and the various types of satellite that amateur radio uses.   A look at antenna’s and the effects of doppler shift leading to the need to correct frequencies followed.  Stephen also gave information on which frequencies to listen on and some very useful websites for those of us who wanted to try it out for ourselves.

The talk was very well received and Stephen gave a demonstration after the talk using the equipment in the club radio shack.

Mary G6SWZ

Photo Alistair M0TEF

 Posted by at 8:27 pm
Dec 042018
 

Wednesday 21st saw the LSWC hold their annual Construction Contest for the Joe Rose Memorial Trophy. Last year saw us two different versions of ATV transmitter. One being for home use including a partly assembled water cooled power amplifier (For an update see below) built by Adrian M0NWK. The second, and also the winner for last year, being a fully portable transceiver in a case built by Jason G7KWP.

Adrian M0NWK

This year Started off with a similar theme. Adrian M0NWK, started off by showing us his Arduino powered controller for a comtech 23cm ATV transmitter.

 

 

 

 

 

 

 

This was achieved by removing the dip switches from the transmitter and replacing them with a SSR (Solid State Relay) board. These relays are then controlled by the Arduino which also shows the selected frequency on the front LCD.

Adrian also showed us the completed Water Cooled Power Amplifier which was shown the previous year. Also shown was an Arduino controlled Temperature monitor.

 

 

 

 

 

 

 

 

Andy G0FVI

Next up was Andy G0FVI. Who has constructed an 80m CW receiver which will eventually become a transceiver in time. By choosing an IF of around 10.695 this allowed him to use bits from numerous scrap 11m radios he had laying around.

 

 

 

 

 

 

 

 

 

 

 

  • The bandpass filter was fabricated from two Toko type ferrite core coils.
  • The first mixer is based around an SA612 chip and also provides amplification. In retrospect this may have been a bad idea as the chip does produce a few ‘birdies’ although they are well below main signal level.
  • The VFO is an Alan Lake design for 80m with the L/C of the tuned circuit changed to give an output of 7.2-7.1 MHz.  Output is buffered in the VFO enclosure and this is fed to the 1st mixer.
  • Output of the 1st mixer is fed to a 10.7 MHz XTAL filter with a bandwidth of about 15-20KHz.
  • The IF amp is based around an MC1350 IC.  Negative DC feedback from following stages provide AGC action (fast/slow).
  • Demodualtion to provide audio out is achieved using a diode ring mixer. Such a mixer provides a nice clean output with little spurious signals. A 10.695 MHz signal is fed into the ring mixer (together with IF).
  • Demodulated audio is fed to a 2 transistor pre-amp which also provides DC feedback for AGC. Audio is sampled at this stage and fed to another transistor amp to drive the signal meter (taken from an 11m walkie talkie!).
  • The audio stage is based on a rather ancient LM380N!

All stages were built and tested using a sig gen/scope etc. before being connected. Great care was taken with the construction of the VFO, whose spectral purity I was finally able to look at using an SDRplay RSP1A and a beta release spectrum analyser app.

Controls are IF (RF) gain, volume, RIT, AGC fast/slow and VFO.

When I complete this I will add a prefabricated board for PA and some TX/RX switching (should just about fit). I will sample VFO and mix with TX XTAL oscillator, add some filtering and off to PA. Might be an idea to have a go at matching XTAL filter in the receiver too.

 

 

 

 

 

 

 

 

 

David G6MAF

Next up was David G6MAF. Who had constructed a RF tap, or signal monitor which covered 2-30MHz. A device like this is very useful for monitoring your own transmissions by connecting straight into the feed line. With 50 ohms through to the antenna from the transmitter, a second output is taken and attenuated for feeding into a device such as a spectrum analyser etc…

 

 

 

 

 

 

 

 

 

Bob G4PDF

For the final item we made full circle as Bob, G4PDF, showed off his portable 5GHz ATV Transceiver. The equipment was all installed in a box which was mounted to the back of the dish which was then fixed to a tri-pod. The transceiver included a screen overlay showing his Callsign and also converted a received GPS signal into a locator which is also displayed.

 

 

 

 

 

 

 

 

 

 

The Winner

It was at this point after all had builds had been shown that contestants left the room for the remaining to vote on who’s they thought was the best. After discussions about complexity, imagination, modules or scratch built & uniqueness, the vote was in.

 

The contestants were called back in and the Winner was…… Bob G4PDF, with his 5GHz ATV.

 

The trophy will be awarded at the clubs AGM.

Dec 022018
 

LSWCs ever popular Surplus Equipment Sale took place on Wednesday 31st October in the Village Hall at Aisthorpe when regular attendees from the East Riding of Yorkshire, Nottinghamshire, Derbyshire and, of course, Lincolnshire were able to off load their surplus equipment and pick up a few bargains.  The date of our next sale is 24th April 2019.

A couple of the lots

         

Our visitors (and some members)

 Posted by at 8:16 pm
Dec 022018
 

Record numbers attended this year’s National Hamfest which was held on the 28th and 29th September.  The George Stephenson Hall was filled with traders from around the UK and Europe together with Clubs and Special Interest Groups and RSGB Books and RSGB Committees.  There was a large flea market area and outside traders together with the Bring and Buy marquee and Camb Hams with Flossie running GB18NH.

Below are a few photos to remind you of this year’s Hamfest or to show you what you missed.

   

 Posted by at 12:28 am